Products in "DC Gear Motors" category at AllElectronics.com http://www.allelectronics.com/?page=rss&action=category_products&id=17507 Fri, 10 Sep 2010 08:30:06 -0400 6 RPM GEARHEAD MOTOR http://www.allelectronics.com/make-a-store/item/DCM-245/6-RPM-GEARHEAD-MOTOR//1.html Fri, 10 Sep 2010 08:30:06 -0400 6 RPM GEARHEAD MOTOR Powerful little 6-12 Vdc gearhead motor. 2.43" long, excluding shaft. 1.3" diameter x 1.15" long gearbox. Flatted 0.2" diameter x 0.39" long offset shaft. Three tapped mounting holes on motor face. No-load ratings: 3 RPM, 6 Vdc, 75 mA. 6 RPM, 12 Vdc, 85 mA.

Our Price: $13.75

]]> 12VDC MIRROR ADJUSTER MECHANISM http://www.allelectronics.com/make-a-store/item/DCM-273/12VDC-MIRROR-ADJUSTER-MECHANISM//1.html Fri, 10 Sep 2010 08:30:06 -0400 12VDC MIRROR ADJUSTER MECHANISM Automotive side-view mirror assembly consists of two small 12 Vdc motors with push/ pull worm-gear mechanisms. The motors raise and lower a 4.28" square plastic platform. The worm-gear mechanisms can push or pull depending on polarity and will allow manual adjustment without voltage present. Each motor / worm-gear assembly is independent, protected with a rubber boot for moisture protection. The motors can be separated from the larger assembly by breaking off the mirror platform (see instructions). Overall thickness of motors and platform is approximately 2". See larger picture for view of individual motors.

Our Price: $3.00

]]> 5 RPM GEAR MOTOR, 12VDC http://www.allelectronics.com/make-a-store/item/DCM-276/5-RPM-GEAR-MOTOR-12VDC//1.html Fri, 10 Sep 2010 08:30:06 -0400 5 RPM GEAR MOTOR, 12VDC Rugged 5 RPM gear motor designed to move baffles in automotive air conditioning. Ideal for continuous or intermittent use where power, slow rotation, low noise and low current are desired. Drive mechanism consists of a small DC motor with a worm gear driving a four gear train. Final drive is a plastic splined shaft, 0.52" diameter x 0.5" long. The composite plastic housing is easily opened for access to the motor, gears and electrical terminals. Overall dimensions of assembly including mounting flanges and shaft is approximately 3.12" x 4.25" x 1.62." No load measurements: 5 RPM @ 13.5 Vdc @ 15 mA.

Our Price: $9.00

]]> GEARHEAD, USED http://www.allelectronics.com/make-a-store/item/GH-2/GEARHEAD-USED//1.html Fri, 10 Sep 2010 08:30:06 -0400 GEARHEAD, USED Mates with Faulhaber 2342 and similar motors with four mounting holes on 26mm centers and an 11mm dia. mating gear with 18 teeth. Gearbox dimensions:32mm x 32mm x 25mm. 6mm dia. shaft is 35mm long. Exact specs unknown. Final rotational speed was approximately 120RPM when used with Faulhaber 2342 motor at 12Vdc. Price reduced.

Our Price: $3.75

]]> 24 VDC GEAR MOTOR W/ TURNTABLE http://www.allelectronics.com/make-a-store/item/DCM-351/24-VDC-GEAR-MOTOR-W/TURNTABLE/1.html Fri, 10 Sep 2010 08:30:06 -0400 24 VDC GEAR MOTOR W/ TURNTABLE Relatively powerful, low-current DC motor and gearbox with a 4.9" diameter plastic (nylon?) turntable with a rubber o-ring circumference that could be used to drive another wheel. Turntable can be removed from motor and rubber ring on turntable can be removed as well. Motor gearbox has a 5/16" diameter shaft that is flatted and splined.

Specifications:
45RPM @ 24 Vdc, 60mA - operates at 12Vdc at 1/2 speed. Drive motor - Mabuchi RS-380SH. 1.1" diameter x 1.67". Gearbox - Molon #CHM-2435-1. 2.75" x 3.00" x 0.57" Threaded mounting holes in four corners. 5/16" diameter shaft, flatted and splined.

Our Price: $9.75

]]> 24 VDC GEAR MOTOR http://www.allelectronics.com/make-a-store/item/DCM-387/24-VDC-GEAR-MOTOR/1.html Fri, 10 Sep 2010 08:30:06 -0400 24 VDC GEAR MOTOR Globe 415A197. 980 RPM @ 24VDC / 90 mA (no-load rating). Will operate as low as 4.5Vdc. 30mm diameter x 45mm long motor. 35mm diameter x 24mm long gear housing. 5mm diameter x 18mm long flatted shaft. Three threaded mounting holes on gearbox face. 115mm leads.

Our Price: $11.75

]]> 10-42 RPM RIGHT-ANGLE DC GEAR MOTOR W/ ENCODER http://www.allelectronics.com/make-a-store/item/DCM-393/10-42-RPM-RIGHT-ANGLE-DC-GEAR-MOTOR-W/ENCODER/1.html Fri, 10 Sep 2010 08:30:06 -0400 10-42 RPM RIGHT-ANGLE DC GEAR MOTOR W/ ENCODER Buehler # 1.61.031.119.00. No-load Ratings: 10 / 21 / 42 RPM @ 6 / 12 /24 Vdc @ 250Ma. 5Vdc, TTL compatible, 50 pulse/RPM encoder mounted on rear. Overall length, 185mm (7.25"). Motor diameter, 54mm (2.13"). 8mm diameter shaft is 48mm long. Shaft is held in place with a collar and set screw and can be removed and re-installed facing the opposite direction. Three tapped mounting holes on face of gearbox. Two 6" leads to motor. 4", 3-conductor flat cable to encoder. A relatively quiet and powerful motor.

Our Price: $30.00

]]> 40/80 RPM DC GEAR MOTOR http://www.allelectronics.com/make-a-store/item/DCM-396/40/80-RPM-DC-GEAR-MOTOR/1.html Fri, 10 Sep 2010 08:30:06 -0400 40/80 RPM DC GEAR MOTOR Buehler # 1.61.046.115.00. No load ratings: 40 RPM @ 12Vdc / 50 mA, 80 RPM @ 24Vdc /65 mA. Dimensions: Overall length, 69mm. Motor diameter, 31mm. Gear box diameter, 35mm. 5mm flatted shaft is 17mm long. 40mm leads w/ 2-pin connector.

Our Price: $14.95

]]> 72 / 144 RPM GEAR MOTOR http://www.allelectronics.com/make-a-store/item/DCM-389/72/144-RPM-GEAR-MOTOR/1.html Fri, 10 Sep 2010 08:30:06 -0400 72 / 144 RPM GEAR MOTOR Buehler # 1.61.046.132.00. No-load ratings: 72 RPM @ 12Vdc 25mA, 144 RPM @ 24Vdc 30mA. Overall length, 69mm. Gearbox diameter 35mm. 5mm diameter x 26mm long flatted shaft. Three tapped mounting holes in gearbox face. 75mm leads.

Our Price: $12.95

]]> 62 / 124 RPM DC GEAR MOTOR http://www.allelectronics.com/make-a-store/item/DCM-390/62/124-RPM-DC-GEAR-MOTOR/1.html Fri, 10 Sep 2010 08:30:06 -0400 62 / 124 RPM DC GEAR MOTOR Buehler # 1.61.046.131.00. No-load Ratings: 62 RPM @ 12Vdc, 124 RPM @ 24Vdc. Overall length, 65mm. Gearbox diameter, 35mm. 5mm diameter x 26mm long flatted shaft. Three tapped mounting holes in gearbox face. Recessed 2-pin female connector. Our connector, CAT# CON-230P, though not ideal, will enable connection to the motor.

Our Price: $14.00

]]> RIGHT-ANGLE DC GEAR MOTOR, 30-60 RPM http://www.allelectronics.com/make-a-store/item/DCM-392/RIGHT-ANGLE-DC-GEAR-MOTOR-30-60-RPM/1.html Fri, 10 Sep 2010 08:30:06 -0400 RIGHT-ANGLE DC GEAR MOTOR, 30-60 RPM Buehler # 1.61.031.107.03. No-load ratings: 30RPM @ 12Vdc / 90Ma, 60RPM @ 24Vdc @ 100mA. Powerful, quiet, right-angle gear motor. Overall length, 134mm (5.25"). Motor diameter, 40mm (1.58"). 10mm flatted shaft is 34mm long. Three tapped mounting holes on face of gearbox. Detachable 2-pin connector with 4" leads plugs in at end of motor.

Our Price: $26.00

]]>