|
Vibrating motor with offset weighted shaft. Fairly vigorous vibration at 3Vdc, 150mA. Works on 1.5-4.5Vdc. Motor is 0.9" diameter x 1.05" long. Weight is 0.81" diameter half-moon x 0.22" thick....
CAT# DCM-478
$1.50 each
100
to 239
$1.25 each
240
or more
$1.10 each
|
Mabuchi # RE280RA. Useful in many hobbyist projects such as radio controlled vehicles, robotics, model-building, home automation, and more! 30mm long x 24mm diameter. 2.0mm diameter shaft x 12mm l...
CAT# DCM-487
2
for $1.00
Minimum order of 2
pieces
.
|
|
|
Hexin P/N 14011305. 1.5 RPM timing-type motor. Clock-wise rotation. Operates on 120Vac, 60Hz, 3W. 0.25" (6.5mm) flatted shaft is 0.75" long. Oval, 63 x 49 x 23mm deep. Two mounting holes on 48mm (1...
CAT# ACM-135
$4.25 each
|
Mabuchi # RE-280RA 08238A. 23.8mm diameter x 30.5mm long. Shaft: 2mm diameter x 12mm long. No-load measurement: 150mA @ 3Vdc. There is a 9mm diameter x 3mm button on the back of the motor that serv...
CAT# DCM-436
$1.75 each
|
|
|
Turnigy, Plush 10A Brushless Speed Controller. Designed for use with Remote Control model vehicles. Continuous Current: 10A Burst Current: 12A BEC Mode: Linear BEC : 5v / 2A Lipo Cells: 2-4 NiMH :...
CAT# SC-110
$16.50 each
|
Elinco WH-1276. Low-noise, capacitor-run reversible 115Vac, 0.2A, continuous-duty motor with a 5mm diameter x 10mm toothed shaft designed to mate with a gear head. 1450 RPM. 61mm square mounting pl...
CAT# ACM-276
$11.50 each
|
|
|
Mabuchi #RK 370CA. 24.4mm diameter x 30.8mm long. 2mm diameter x 8mm shaft. Optimum performance around 18 - 24Vdc. Operates as low as 4Vdc. Two M3.0x0.5 tapped holes in motor face. Solder termina...
CAT# DCM-375
$1.75 each
10
to 99
$1.65 each
100
or more
$1.50 each
|
Chrysler left-hand window-lift motor. 12 Vdc, 3.5A, 88RPM (no load). Powerful, right-angle worm-gear drive. 18mm diameter gear on 47mm turntable rotates around 8mm shaft. Center shaft is stationar...
CAT# DCM-565
$14.95 each
|
|
|
Chrysler right-hand window-lift motor. 12 Vdc, 3.5A, 88RPM (no load). Powerful, right-angle worm-gear drive. 18mm diameter gear on 47mm turntable rotates around 8mm shaft. Center shaft is station...
CAT# DCM-572
$14.95 each
|
No-load measurements: 520 RPM @ 12Vdc, 250mA. Works as low as 3Vdc (approx. 100RPM). Overall length, 57mm. Gearbox, 27mm diameter x 23mm long. Motor, 24mm diameter x 30mm long. Flatted shaft, 6mm d...
CAT# DCM-475
$9.50 each
|
|
|
Igarashi Motor # 3657-070-GF-5. 8100RPM @ 24VDC, 0.2A (no-load rating). 38mm diameter x 57mm long. 3.2mm diameter x 20.0mm long shaft. Two M3.0 x 0.5 tapped holes in motor face on 0.984" centers. S...
CAT# DCM-369
$3.00 each
|
Mabuchi RS-385PH. 29mm diameter x 38mm long. 2.3mm diameter x 14mm long shaft. Two tapped mounting holes, M2.6 x 0.45, on 16mm centers on motor face. 18 Vdc, 0.23A no load. Solder terminals.
CAT# DCM-465
$2.75 each
10
or more
$2.60 each
|
|
|
Mabuchi# RS555PH-23300A. 12 Vdc motor with 5-pole construction utilizes permanent magnet so that the motor produces high torque with high efficiency. Speed without load, 5560 rpm, Current draw, at ...
CAT# DCM-471
$4.50 each
10
or more
$4.00 each
|
Canon# EN35-T101Z1A. 12 vdc motor prepped with circuit board and 11" insulated 3 conductor wire. No load rating: 4,000RPM @ 30mA. 34mm diameter x 32mm long body. 3mm diameter x 10mm long shaft.
CAT# DCM-477
$1.20 each
10
or more
$1.00 each
|
|
|
Textron # 601396. Powerful, smooth-running 12 Vdc motor for window washer application. Rated at 12 Vdc 400ma no-load. Will operate on 1-12 Vdc. 1.08" diameter x 1.72" long. Flatted shaft measures ...
CAT# DCM-482
$4.00 each
|
No-load rating: 180 RPM @ 12Vdc / 1.3A. Overall length, 144mm (5.66"). Motor diameter, 49mm (1.91"). 12mm diameter worm shaft is 89mm (3.55") long. The last 12mm of the shaft has a 6 x 1.0 reverse ...
CAT# DCM-563
2 Available
$17.95 each
|
|
|
No-load rating: 180 RPM @ 12Vdc / 1.3A. Overall length, 144mm (5.66"). Motor diameter, 49mm (1.91"). 12mm diameter worm shaft is 89mm (3.55") long. The last 12mm of the shaft has a 6 x 1.0 reverse ...
CAT# DCM-697
$17.95 each
|
Brand unknown - Made in Belgium# PD 12. Code number : 9904 112 12001. 3 Deg. 45' step angle. 175mA. 150 g/cm torque. 1.5" diameter x 2.48" long. 1.5" square mounting plate. 0.15" diameter x 0...
CAT# SMT-118
$3.75 each
|
|
|
Turnigy Plush 18A brushless speed controller. Outstanding performance, fast sync timing to accomodate a broad range of motors. Continuous Current: 18A Burst Current: 22A BEC Mode: Linear BEC : 5v ...
CAT# SC-118
$21.00 each
|
Mabuchi # FF-030PA 08250. Body: 15.5 x 12 x 20mm long. Shaft: 1.5mm diameter x 6mm long. Two tapped mounting holes on 10mm centers, ISO M2.0 x 0.4. No-load rating: 6Vdc, 41mA, 10,500 RPM. Solder te...
CAT# DCM-433
$1.25 each
100
or more
$1.05 each
|
|
|
Barber-Colman # 1-1928A FYQM. 31.5mm diameter x 50mm long. 3mm diameter x 12mm long shaft. Good quality motor, operates smoothly on 18-24 Vdc. 24 Vdc, 0.20A no load. Two tapped mounting holes on m...
CAT# DCM-456
$3.00 each
|
Relatively powerful, low-current DC motor and gearbox with a 4.9" diameter plastic (nylon?) turntable with a rubber o-ring circumference that could be used to drive another wheel. Turntable can be ...
CAT# DCM-351
$9.75 each
|
|
|
Operates on 18-30 Vdc. 24 Vdc, 0.2A no-load rating. 36mm diameter x 57mm long. 3mm diameter x 20mm long shaft. Solder/qc terminals and shaft on the same end.
CAT# DCM-461
$1.75 each
10
or more
$1.50 each
|
Relatively powerful, low-current DC motor and gearbox. Motor gearbox has a 5/16" diameter shaft that is flatted and splined. Specifications: 45RPM @ 24 Vdc, 60mA - operates at 12Vdc at 1/2 speed...
CAT# DCM-469
$9.65 each
|
|
|
Turnigy Plush 25A brushless speed controller with new powerful microprocessor. Outstanding performance, ultra-fast sync timing to accommodate a broad range of motors. Also there is a separate volta...
CAT# SC-125
$24.00 each
|
25mm (1") diameter x 12mm stepper motor. 6 leads, 3" long. Mounting holes on 35mm centers. 3.5mm diameter threaded shaft.
CAT# SMT-136
$2.00 each
|
|
|
Operates on 1.5-4.5 Vdc. Motor is 0.9" diameter x 1.05" long. 2mm diameter shaft. Solder-loop terminals.
CAT# DCM-480
$1.55 each
10
or more
$1.45 each
|
Johnson Motor #63240. 35.5mm diameter x 50mm long. 3mm diameter x 9mm long shaft. No-load rating: 6vdc, 1.2A. Gold-plated solder terminals.
CAT# DCM-474
$2.35 each
10
or more
$2.10 each
|
|
|
Mabuchi # RE280RA. Useful in many hobbyist projects such as radio controlled vehicles, robotics, model-building, home automation, and more! 30mm long x 24mm diameter. 2.0mm diameter shaft x 12mm l...
CAT# DCM-464
$0.95 each
100
or more
$0.65 each
|
BEI # DIH23-30-0132. Smooth, quiet, high-torque brushless DC motor. 2.25" diameter x 3.0" long. 0.25" diameter x 1" long shaft. 5270 RPM with no load. Built in speed sensor. 7-15Vdc operating volta...
CAT# DCM-459
$16.95 each
|
|
|
Lots of power from this compact combination of 3-phase brushless DC motor and low-speed gear box. Heavy duty worm gear drive gearbox with grease fitting. 10mm square shaft is tapped with 5/16-18 ...
CAT# DCM-473
$30.00 each
|
Relatively powerful little motor. 13,000 RPM @ 6Vdc / 250 Ma. 1.08" diameter x 1.83" long. 2mm diameter shaft with a 9mm gear. Red and black 18 AWG wire leads with miscellaneous connectors.
CAT# DCM-485
$2.50 each
10
or more
$2.25 each
|
|
|
Mabuchi #RF-130CH 12250. Body: 17mm diameter x 22.5mm long (0.67" D x 0.91" L). Shaft: 1.5mm diameter x 8.6mm long. Operates on 2 - 6 Vdc. No load Spec: 8100 RPM @ 6vdc, 0.036A. At maximum ...
CAT# DCM-454
$1.20 each
50
to 99
$1.10 each
100
to 799
$1.00 each
800
or more
$0.90 each
|
Nissei Denki motor. 29.4mm long x 20.0mm diameter. Shaft, 10mm long x 1.5mm diameter. No-load specs: 12,000 RPM @ 6 Vdc, 40mA. Operates on 1-8 Vdc range. Two threaded mounting holes on motor face ...
CAT# DCM-410
$1.35 each
100
or more
$1.05 each
|
|
|
New gear head motor prepped with an arm that rotates an offset axle in a 1" circle. Can be used to facilitate reciprocating action. Motor is 1.45"D x 3.00"L. No-load specs: 25RPM @ 6Vdc, 150mA. Pr...
CAT# DCM-470
$5.75 each
|
Nichibo # UC-280P-19160TBNRCE. No-load specs: 11,500 RPM @ 12.0V DC, 0.15 A. At Maximum efficiency: 9,000 RPM @ 12V DC, 0.57A - 46 g-cm torque. 30.5mm long x 18.3mm x 24mm. 2mm diameter x 11mm lo...
CAT# DCM-427
$1.00 each
10
to 199
$0.90 each
200
or more
$0.80 each
|
|
|
Johnson Motor HC613LG-6411. A fairly powerful motor, probably designed for 6-12Vdc. Operates as low as 2Vdc. Requires about 1.5A @ 12Vdc, no load. 37mm diameter x 57mm long. 3mm diameter shaft...
CAT# DCM-462
$2.25 each
10
or more
$2.00 each
|
High speed permanent magnet motor 6-24VDC with tach output. 10,000 RPM @ 20Vdc, 150mA (no-load). 34mm dia. x 55mm long. 3mm dia shaft with pulley. Four 90mm leads w/ 4-pin female connector (0.1").
CAT# DCM-408
$4.25 each
10
or more
$3.85 each
|
|
|
Mabuchi # FK-130SH. 25.1mm long x 15.4mm x 20.4mm (0.99" x 0.61" x 0.80"). 2mm diameter shaft. 8mm long. Nominal, no-load ratings: 7200 RPM @ 12Vdc @ 0.30A. Solder-loop terminals.
CAT# DCM-476
$1.20 each
50
to 599
$1.05 each
600
or more
$0.90 each
|
Mabuchi # FK-130SH. 25.1mm long x 15.4mm x 20.4mm (0.99" x 0.61" x 0.80"). 2mm diameter shaft. 8mm long. Equipped with 5.8mm diameter brass gear and 45mm leads. Nominal, no-load ratings: 7200 RPM ...
CAT# DCM-476W
$1.25 each
50
to 199
$1.10 each
200
or more
$1.05 each
|
|
|
Minebea Astrosyn # 23BB-H051-21. 5V 7.5 degree 6.6-ohm coil stepper motor. 56.5mm diameter x 25mm excluding 1/4" shaft. Six 15" wire leads terminate to 10 pin connector. Mounting flanges with 65mm...
CAT# SMT-382
$2.00 each
|
Minebea Astrosyn # 23BB-H051-23. 5V 7.5 degree 6.6-ohm coil stepper motor. 56.5mm diameter x 25mm excluding shaft. Attached to the shaft is a 0.50" aluminum cog pulley. Six 6" wire leads terminate...
CAT# SMT-381
117 Available
$2.25 each
|
|
|
Power Electric Distribution 21267-000 Rev.B. 6 Vdc gear motor. No-load rating: 80 RPM @ 6 Vdc,110mA. Works well down to 1.5Vdc (12RPM). 61mm L x 20mm D. 4mm diameter x 11mm flatted shaft. 280mm lea...
CAT# DCM-365
$8.95 each
10
or more
$8.50 each
|
BARBER COLMAN EYQM. 7.5Vdc , 150mA, 3600 RPM (no-load). Runs smoothly in 7.5-15Vdc range. 30.5mm diameter x 54mm long. 3.5mm diameter shaft with a 6.5mm diameter pulley. The motor has two pairs of ...
CAT# DCM-420
$4.50 each
|
|
|
Mabuchi #FC-280PT-20150. 24.2 x 18.3 x 30.5mm long, excluding shaft. 2mm diameter x 9mm long splined shaft. No-load rating: 11,800 RPM @ 12Vdc, 0.56A. Push-in-style terminals. Push wire into slots ...
CAT# DCM-374
$1.25 each
10
to 99
$1.15 each
100
or more
$0.95 each
|
Hansen Corp # 237500-342. 5V 7.5 degree 6.6-ohm coil stepper motor. 56.5mm diameter x 25mm excluding 1/4" shaft. Eight 12" wire leads. Mounting flanges with 65mm centers.
CAT# SMT-383
$2.25 each
|
|
|
Minebea Astrosyn Type 23LM-K255-03. NEMA 23 bipolar stepper motor. 1.8 degree per step. 57 x 57mm mounting plate. 57mm diameter x 40mm long, excluding shaft. 6.5mm diameter x 23mm long shaft. Eight...
CAT# SMT-135
$8.50 each
|
33JPF-15380-50. Quality 12Vdc gearmotor runs 85rpm @ 42mA (no-load), but has input voltage range from 2 - 20vdc. At 12vdc draws about 160ma typical under load. Overall length excluding shaft - 50mm...
CAT# DCM-416
$8.75 each
10
or more
$7.75 each
|
|
|
Artek, Apse 60. Band brake for electric scooter. 60mm drum fits threaded 35mm diameter hub.
CAT# BB-60
$4.50 each
|
Buehler# EC775596. 12 Vdc 200 mA, 5600 RPM. 34mm dia. x 55mm long. 3mm dia shaft with pulley.
CAT# DCM-455
$4.25 each
10
or more
$3.85 each
|
|
Customer Service: 818-904-0524 | Toll Free Order Line: 1-888-826-5432
