|
10 x 12 x 15mm long Mabuchi motor. 1mm diameter shaft. Solder terminals.
CAT# DCM-403
$1.25 each
|
Mabuchi # SH-020. Small, relatively powerful DC motor. Appears to operate best between 1.5 and 3Vdc. Draws 570mA @ 1.5Vdc (no load). Rectangular body, 19 x 18 x 10mm. 1.5mm shaft w/ 4mm brass gear...
CAT# DCM-402
$1.50 each
|
|
|
Howard Industries # 1175-06-4. 115Vac, 11W shaded pole motor. 3" x 2.5" x 1.1". Mounting holes on 1.95" centers. 1.05" diameter spindle with tapped holes on 0.85" centers. 18" leads.
CAT# ACM-341
$3.00 each
|
Elinco WH-1276. Low-noise, capacitor-run reversible 115Vac, 0.2A, continuous-duty motor with a 5mm diameter x 10mm toothed shaft designed to mate with a gear head. 1450 RPM. 61mm square mounting pl...
CAT# ACM-276
$16.00 each
|
|
|
Thomson Airpax # L81791-U4-M7. 115 Vac, capacitor-run, reversible motor. 50/60Hz. 250/300 RPM. 57mm diameter x 25mm. Mounting flange with holes on 68mm centers. 6mm diameter x 13mm long shaft. 330...
CAT# ACM-127
$5.00 each
|
New motor and gearhead, pre-asssembled, with mounting plate and 6uF capacitor. Oriental Motor # 4RJ20GB-AUL. Capacitor-run, single-phase motor with built-in friction brake to improve instantaneou...
CAT# ACM-129
$70.00 each
|
|
|
Oriental Motor# 4RJ20GB-AUL. Capacitor-run, single-phase motor with built-in friction brake to improve instantaneous reversing characteristics. Suited for applications where the motor must switch d...
CAT# ACM-420
$25.00 each
|
Mabuchi #RK 370CA. 24.4mm diameter x 30.8mm long. 2mm diameter x 8mm shaft. Optimum performance around 18 - 24Vdc. Operates as low as 4Vdc. Two M3.0x0.5 tapped holes in motor face. Solder termina...
CAT# DCM-375
$1.75 each
10
to 99
$1.65 each
100
or more
$1.50 each
|
|
|
Pittman #8224C106-R5. No-load Ratings: 1700 RPM @ 6Vdc / 0.8Amp, 3700 RPM @ 12Vdc / 1Amp. 30mm diameter x 61.7mm long. 2.5mm diameter x 5.9mm flatted shaft. Motor face has 4 tapped mounting holes. ...
CAT# DCM-704
$5.50 each
|
Sayama #12SM-AT3. Compact, good-quality 12Vdc gearhead motor. 58RPM, @ 12Vdc, 20mA (no-load). 12mm diameter x 35mm long. Solder-lug terminals. 2mm diameter x 6mm long flatted shaft.
CAT# DCM-318
$12.95 each
|
|
|
Merkle-Korff S1624. 150 RPM @ 12Vdc, 310mA (no-load). Motor dimensions: 40mm diameter x 62mm long. Gear box dimensions: 51mm diameter x 29mm long. 6.5mm (0.25") flatted shaft is 18mm long. 200mm p...
CAT# DCM-363
$16.00 each
|
Canon Precision #DN26-T41N1B. 4,000 RPM @ 12Vdc / 25mA - No Load. 25.5mm diameter x 25mm long. 2mm diameter x 13mm shaft. Two threaded 3mm mounting holes on 17mm centers. Solder-loop terminals.
CAT# DCM-300
$2.00 each
10
or more
$1.75 each
|
|
|
Igarashi Motor # 3657-070-GF-5. 8100RPM @ 24VDC, 0.2A (no-load rating). 38mm diameter x 57mm long. 3.2mm diameter x 20.0mm long shaft. Two M3.0 x 0.5 tapped holes in motor face on 0.984" centers. S...
CAT# DCM-369
$3.00 each
|
36mm diameter x 26mm long. 2mm diameter x 10.5mm long shaft. Operates smoothly between 12 and 36Vdc. Three tapped mounting holes on face of motor. Solder-lug terminals.
CAT# DCM-448
$2.00 each
|
|
|
Buehler #1.61.046.503.06. No load ratings: 110 RPM @12Vdc/90mA. 250 RPM @ 24Vdc/90 mA. Overall length, excluding shaft, 75mm. Gear head diameter, 35mm. Flatted shaft, 5mm diameter x 19mm long with ...
CAT# DCM-441
$14.95 each
|
Buehler # 1.13.022.232.00. No load ratings: 4500 RPM @12Vdc/80mA. 10000 RPM @ 24Vdc/100mA. 31.2mm diameter x 54.73mm long. Shaft 2.47mm diameter x 25 mm long with 11.8mm diameter plastic worm gear...
CAT# DCM-445
$6.00 each
|
|
|
Automotive side-view mirror assembly consists of two small 12 Vdc motors with push/ pull worm-gear mechanisms. The motors raise and lower a 4.28" square plastic platform. The worm-gear mechanisms c...
CAT# DCM-273
$3.00 each
|
No-load rating: 180 RPM @ 12Vdc / 1.3A. Overall length, 144mm (5.66"). Motor diameter, 49mm (1.91"). 12mm diameter worm shaft is 89mm (3.55") long. The last 12mm of the shaft has a 6 x 1.0 reverse ...
CAT# DCM-563
$19.95 each
|
|
|
No-load rating: 180 RPM @ 12Vdc / 1.3A. Overall length, 144mm (5.66"). Motor diameter, 49mm (1.91"). 12mm diameter worm shaft is 89mm (3.55") long. The last 12mm of the shaft has a 6 x 1.0 reverse ...
CAT# DCM-697
$19.95 each
|
Brand unknown - Made in Belgium# PD 12. Code number : 9904 112 12001. 3 Deg. 45' step angle. 175mA. 150 g/cm torque. 1.5" diameter x 2.48" long. 1.5" square mounting plate. 0.15" diameter x 0...
CAT# SMT-118
$4.75 each
|
|
|
Vexta #PH264-E1.5-C5. 2.25Vdc @ 1.5A 2-Phase 1.8°/step. 56.5mm x 56.5mm square flange with tapped mounting holes on 46.73 centers. 56.55mm diameter x 41.28mm long motor. 6mm diameter flatted s...
CAT# SMT-367
$12.00 each
|
Airpax # S94-0200. 24VAC 60Hz, capacitor run, gear motor. 52.5mm diameter x 45mm. Shaft is 5.5mm diameter x 41mm long with a 9.5mm copper bushing on the lower 11mm of the shaft. Three tapped mounti...
CAT# ACM-200
$6.50 each
|
|
|
Cramer 800HN. Permanent magnet gear motor. 50RPM @ 24Vdc, 20mA. Counter-clockwise rotation. 3.5mm diameter x 20mm long shaft, knurled lower half. Pear-shaped gear box, 61.00 x 46.83mm. Overall le...
CAT# DCM-364
$7.50 each
|
Relatively powerful, low-current DC motor and gearbox with a 4.9" diameter plastic (nylon?) turntable with a rubber o-ring circumference that could be used to drive another wheel. Turntable can be ...
CAT# DCM-351
$9.75 each
|
|
|
Portescap #S42L048S02-M5. 24V, 5 Ohm, 7.5 Degree per step. 42mm diameter x 22mm. Two mounting holes on 51mm centers. Four 3" leads. Shaft - 3mm diameter x 11mm long. 16 tooth, 9.75mm diameter ...
CAT# SMT-356
$2.50 each
|
Compact DC gearhead motor. Operates smoothly from 3-12Vdc. 60RPM @ 6Vdc, 110mA (no-load rating). Overall length, 53mm. Diameter of gearhead, 33mm. 5mm diameter x 12mm long flatted shaft. Three tapp...
CAT# DCM-702
$15.00 each
|
|
|
Mabuchi #RS-555PH. 12Vdc (9-20V) motor. Approximately 4500RPM @ 12Vdc, 0.15A (no load rating). 37mm diameter x 58mm long. 3.2mm diameter x 13mm long flatted shaft. Solder-lug terminals.
CAT# DCM-330
$3.50 each
|
Timing-style gear motor, removed from working equipment in good condition. Operates over a 3-20Vdc range, approximately 20ma @ 3Vdc, 80ma @ 20Vdc. 176RPM @ 12Vdc. Pear-shaped gear box, 65 x 49mm, t...
CAT# DCM-395
$4.75 each
|
|
|
Thomson Airpax Mechatronics # S42M048T52. 3.1Vdc, 3.6 Ohm, 7.5 Degree per step. 42mm diameter x 22mm. Four mounting holes on 36mm centers. Four 6" leads. Shaft - 3mm diameter x 11mm long. 13 t...
CAT# SMT-355
$2.50 each
|
Crouzet 80807.8. 3000 RPM motor with a 250:3 gear head. Final drive is 31 RPM @ 24Vdc, 400mA (no-load). Powerful for its size. Motor is 90mm long x 43mm diameter. Gear box is 65 x 65 x 35mm. Shaft ...
CAT# DCM-366
$19.95 each
|
|
|
Shinano Kenshi # STP 58D3004. 56 x 56 x 54mm stepper. 1.8 Degree per step. 0.48 Ohm. Four mounting holes on 47mm centers. Four 4" wire leads prepped with 5-pin connector. 6.5mm (0.25") diameter ...
CAT# SMT-119
$14.00 each
|
Mineba NMB-MAT # PM42L-048-UAJ9. 24V stepper motor. 48 steps per revolution, 7.5 Deg per step. 2-2 phase. 7 Ohm coils. 42mm diameter x 22mm long. 3mm diameter shaft with brass gear (9.5mm diame...
CAT# SMT-112
$2.50 each
|
|
|
Minebea # 23KM-K217-P2V. 56 x 56 x 42mm stepping motor. Four mounting holes on 47.14mm centers. 1.8 degrees per step. 8mm diameter x 25mm long shaft with 20mm diameter cog gear. 4, 380mm wires with...
CAT# SMT-363
$12.00 each
|
Howard Industries # 1-19-4201. 24Vdc. 3.6 Degrees/step. 42 x 42 x 32mm. Shaft: 5mm diameter x 10mm long. Five 6" leads. Two mounting studs on two diagonal corners of motor face.
CAT# SMT-364
$4.35 each
|
|
|
Synchron# M945. 50RPM timing-type = motor. 120VAC, 60Hz, 8W timing motor. Motor is 47mm diameter x 24mm. Gear box is 59mm x 47mm oval x 19mm. 3.5mm (1/8") diameter shaft with brass gear attached. ...
CAT# ACM-93
$5.00 each
|
Powerful little 6-12 Vdc gearhead motor. 2.43" long, excluding shaft. 1.3" diameter x 1.15" long gearbox. Flatted 0.2" diameter x 0.39" long offset shaft. Three tapped mounting holes on motor fa...
CAT# DCM-245
$13.75 each
|
|
|
RS365SH. No-load rating @ 18Vdc: 0.25A, 19400RPM. 27.7mm diameter x 32.6mm long. Shaft is 2.3mm diameter x 15.6mm long. Solder-loop terminals. Motor face has two tapped (M2.6 x 0.45) mounting ho...
CAT# DCM-367
$1.85 each
10
or more
$1.65 each
|
27.7mm diameter x 32mm long. Shaft is 2.3mm diameter x 15.6mm long. 110mA @ 18Vdc (no-load rating). Solder-loop terminals. Motor face has two tapped (M2.6 x 0.45) mounting holes.
CAT# DCM-699
$1.75 each
10
or more
$1.60 each
|
|
|
Sanyo Denki 3.5V, 1.5A, 1.8 Degree/ step. "Step-Syn" 103G770-1854. 57mm diameter x 51mm long motor. 57mm x 57mm square mounting flange with mounting holes on 47.14mm centers. 6.3mm (0.25") diameter...
CAT# SMT-362
$14.00 each
|
North American Philips Controls # 504-0004. 12 Volts, 8 Watt stepper motor. 2.25" diameter x 0.95". 0.25" diameter x 0.37" long shaft. 6" leads. Motors are unused, but discolored from storage con...
CAT# SMT-358
$2.00 each
|
|
|
Buehler # 1.61.046.131.00. No-load Ratings: 62 RPM @ 12Vdc, 124 RPM @ 24Vdc. Overall length, 65mm. Gearbox diameter, 35mm. 5mm diameter x 26mm long flatted shaft. Three tapped mounting holes in gea...
CAT# DCM-390
$14.00 each
|
Power Electric Distribution 21267-000 Rev.B. 6 Vdc gear motor. No-load rating: 80 RPM @ 6 Vdc,110mA. Works well down to 1.5Vdc (12RPM). 61mm L x 20mm D. 4mm diameter x 11mm flatted shaft. 280mm lea...
CAT# DCM-365
$11.95 each
10
or more
$11.50 each
|
|
|
Buehler # 1.61.046.132.00. No-load ratings: 72 RPM @ 12Vdc 25mA, 144 RPM @ 24Vdc 30mA. Overall length, 69mm. Gearbox diameter 35mm. 5mm diameter x 26mm long flatted shaft. Three tapped mounting hol...
CAT# DCM-389
$12.95 each
|
Mabuchi #FC-280PT-20150. 24.2 x 18.3 x 30.5mm long, excluding shaft. 2mm diameter x 9mm long splined shaft. No-load rating: 11,800 RPM @ 12Vdc, 0.56A. Push-in-style terminals. Push wire into slots ...
CAT# DCM-374
$1.25 each
10
to 99
$1.15 each
100
or more
$0.95 each
|
|
|
Johnson Motor #64823 3C4921. 36mm diameter x 50mm long. 3mm diameter shaft x 14mm long. 0.187" QC / solder terminals. Operates smoothly over 8 -24 Vdc range. 5200 RPM @ 14Vdc, 200 ma, no-load rati...
CAT# DCM-398
$3.25 each
|
Airpax® S57M048S02. 5V, 6.25 Ohms/coil, 7.5 Degrees per step. 57mm diameter x 24mm long. Mounting flange with tapped holes on 67mm centers. 5mm diameter x 12mm long shaft with nylon cogbelt pul...
CAT# SMT-133
$3.00 each
|
|
|
Minebea Astrosyn Type 23LM-K255-03. NEMA 23 bipolar stepper motor. 1.8 degree per step. 57 x 57mm mounting plate. 57mm diameter x 40mm long, excluding shaft. 6.5mm diameter x 23mm long shaft. Eight...
CAT# SMT-135
$8.50 each
|
Artek, Apse 60. Band brake for electric scooter. 60mm drum fits threaded 35mm diameter hub.
CAT# BB-60
323 Available
$4.50 each
|
|
|
Artek, Apse 80. Band brake for electric scooter. 70mm drum fits threaded 35mm diameter hub.
CAT# BB-70
180 Available
$6.50 each
|
Compact, relatively powerful DC gear motor. 44 RPM @ 6Vdc/ 70mA (no-load rating). 40.0 x 28.5 x 48.5mm long (1.57" x 1.12" x 1.90"), excluding shaft. 3mm (1/8") diameter flatted shaft x 10mm long. ...
CAT# DCM-401
$12.50 each
|
|
0 items, $0.00 
Customer Service: 818-904-0524 | Toll Free Order Line: 1-888-826-5432
