FirstPrevious • Showing page 1 of 1 (21 items found) • NextLast
Pages: 1
 
Sort Order:
Brand unknown - Made in Belgium# PD 12. Code number : 9904 112 12001. 3 Deg. 45' step angle. 175mA. 150 g/cm torque. 1.5" diameter x 2.48" long. 1.5" square mounting plate. 0.15" diameter x 0... CAT# SMT-118
$4.75 each
Quantity:  
Vexta #PH264-E1.5-C5. 2.25Vdc @ 1.5A 2-Phase 1.8°/step. 56.5mm x 56.5mm square flange with tapped mounting holes on 46.73 centers. 56.55mm diameter x 41.28mm long motor. 6mm diameter flatted s... CAT# SMT-367
$12.00 each
Quantity:  
 
Portescap #S42L048S02-M5. 24V, 5 Ohm, 7.5 Degree per step. 42mm diameter x 22mm. Two mounting holes on 51mm centers. Four 3" leads. Shaft - 3mm diameter x 11mm long. 16 tooth, 9.75mm diameter ... CAT# SMT-356
$2.50 each
Quantity:  
Thomson Airpax Mechatronics # S42M048T52. 3.1Vdc, 3.6 Ohm, 7.5 Degree per step. 42mm diameter x 22mm. Four mounting holes on 36mm centers. Four 6" leads. Shaft - 3mm diameter x 11mm long. 13 t... CAT# SMT-355
$2.50 each
Quantity:  
 
Shinano Kenshi # STP 58D3004. 56 x 56 x 54mm stepper. 1.8 Degree per step. 0.48 Ohm. Four mounting holes on 47mm centers. Four 4" wire leads prepped with 5-pin connector. 6.5mm (0.25") diameter ... CAT# SMT-119
$14.00 each
Quantity:  
Mineba NMB-MAT # PM42L-048-UAJ9. 24V stepper motor. 48 steps per revolution, 7.5 Deg per step. 2-2 phase. 7 Ohm coils. 42mm diameter x 22mm long. 3mm diameter shaft with brass gear (9.5mm diame... CAT# SMT-112
$2.50 each
Quantity:  
 
Minebea # 23KM-K217-P2V. 56 x 56 x 42mm stepping motor. Four mounting holes on 47.14mm centers. 1.8 degrees per step. 8mm diameter x 25mm long shaft with 20mm diameter cog gear. 4, 380mm wires with... CAT# SMT-363
$12.00 each
Quantity:  
Sanyo #B00224. 4-lead, 12Vdc stepper motor. 11.6 Ohm coils. 42mm diameter x 23mm body. Mounting flanges with holes on 50mm centers. 3mm diameter x 13mm long shaft. Prepped with 18mm diameter, ... CAT# SMT-125
$2.50 each
Quantity:  
 
Howard Industries # 1-19-4201. 24Vdc. 3.6 Degrees/step. 42 x 42 x 32mm. Shaft: 5mm diameter x 10mm long. Five 6" leads. Two mounting studs on two diagonal corners of motor face. CAT# SMT-364
$4.35 each
Quantity:  
Sanyo Denki 3.5V, 1.5A, 1.8 Degree/ step. "Step-Syn" 103G770-1854. 57mm diameter x 51mm long motor. 57mm x 57mm square mounting flange with mounting holes on 47.14mm centers. 6.3mm (0.25") diameter... CAT# SMT-362
$14.00 each
Quantity:  
 
North American Philips Controls # 504-0004. 12 Volts, 8 Watt stepper motor. 2.25" diameter x 0.95". 0.25" diameter x 0.37" long shaft. 6" leads. Motors are unused, but discolored from storage con... CAT# SMT-358
$2.00 each
Quantity:  
Airpax® S57M048S02. 5V, 6.25 Ohms/coil, 7.5 Degrees per step. 57mm diameter x 24mm long. Mounting flange with tapped holes on 67mm centers. 5mm diameter x 12mm long shaft with nylon cogbelt pul... CAT# SMT-133
$3.00 each
New Item!
Quantity:  
 
Japan Servo #KP48FP8G-504. 3:25 gear reduction. 7.5 Degrees per step. 24Vdc. 95 Ohms/phase. 6-wire motor. Body is 1.88" diameter x 1.03". L-shape mounting flange on one side, extended mounting... CAT# SMT-359
$2.50 each
Quantity:  
This assembly controlled three servo motors in a commercial photo printer. PC board contains three L6203 Full Bridge Drivers and a socketed microcontroller, AT89S51 24PC. Removed from used equipm... CAT# PCA-3
30 Available
$10.00 each
Web Only!
Quantity:  
 
Nippon Pulse #PF55-48D1. 55mm diameter x 25mm 5V unipolar stepper motor. 7.5 Degrees per step. 2-phase. 5 Ohms per phase. Shaft is 3mm in diameter x 4mm long with a small keyway on one side. Six ... CAT# SMT-120
$2.00 each
Quantity:  
Japan Servo Motor# KH42JM2-038. 6-pin connector, 1.8 Degree/ step motor attached to a gear train with eight single and compound gears. Motor is 42mm square (1.63") x 1.57" long with a 5mm diameter... CAT# SMT-107
$10.00 each
Quantity:  
 
Minebea "Astrosyn" #17BB-H132-11. 4-wire motor with 1/4" diameter x 1" long linear screw shaft and plastic nut that rides up and down the screw. 12Vdc, 75 Ohm. 1.72" diameter x 0.89" body with mo... CAT# SMT-102
$2.75 each
Quantity:  
Novatronics # 20M34R1-A. 5-wire stepper motor with 10 cog pulley attached to shaft. Includes a 14 cog nylon pulley with a 13/32" flatted bore and a 13" circumference cog belt (Gates 23E 09460). T... CAT# SMT-110
$5.50 each
Quantity:  
 
Minebea NMB-MAT #PG35L-048-USCO. Unipolar, permanent magnet stepper motor with gear box. Drive voltage: 12Vdc. Drive method: 2-2 phase. Motor and gear box dimensions: 35mm diameter x 44mm long. Mou... CAT# SMT-365
$6.50 each
Quantity:  
Mabuchi # PF35T-48L4. Four phase, unipolar stepper motor with 6 leads. 3.6 Degree step angle. 20 Ohms. 7V, 350mA. 1.38" diameter x 0.59" long. Mounting flange has two holes on 1.68" centers. Dua... CAT# SMT-108
$3.25 each
Quantity:  
 
Minebea-Matsushita# 23LM-K255-08W P/N 20-0253-01 REV.L. 57mm x 57mm square mounting flange, tapped mounting holes 47.15 centers. 57mm diameter x 40.11mm body. 6.35mm diameter flatted shaft 27.45mm ... CAT# SMT-366
$12.00 each
Quantity:  
 
 
FirstPrevious • Showing page 1 of 1 (21 items found) • NextLast
Pages: 1
 
Sort Order: